Skip Navigation Website Accessibility

 
 

Sewing Machine Tutorial - Kenmore 158.14310

 

 

Getting ready to sew on your Kenmore model 158.14310, but not quite sure where to start? I know how intimidating it can be when you just want to set up your sewing machine, but you can't quite remember how to thread it or use it. Don't worry—here in my sewing studio, we use machines like this every day, and I'm here to show you how to thread it and use it. Let's get into all the amazing features this little machine has to offer.

Video Chapters:

00:00 - Introduction
00:23 - Threading the Upper Machine
03:18 - Inserting the Bobbin & Pulling Up Thread
04:40 - Test Sewing & Built-in Thread Cutter
05:55 - How to Wind a Bobbin
07:29 - Changing & Inserting the Needle
08:18 - Stitch Tension, Patterns & Settings
09:11 - Reversible Single-Hole Needle Plate 1
0:36 - Conclusion

 

1. Threading the Upper Machine

 

To thread the top part of the machine, take your thread and place it on one of the two spool pins. They give you two in case you want to use a twin needle with two threads, which we talk about in another video if you want to see that.

 

Next, guide the thread into the silver guide that opens from the right, and then come down toward the tension disc.

 

Before threading the tension disc, make sure you've raised your presser foot lever from behind. Raising the presser foot opens the tension discs to allow the thread to slip inside properly. Also, turn your flywheel toward you until both the needle and the take-up lever are in their highest positions.

 

Hold the thread up at the top so you can keep tension on it as you bring your left hand around. The thread will settle into the notch. You'll see a little spring wire piece come up and then settle back down as you lift the thread. Double-check that your thread passed between the two discs inside the tension assembly.

 

After the tension disc, bring the thread into the silver guide opening to the right. From there, go through the take-up lever from right to left. Then, drop down into the next silver guide that opens to the right.

 

Above the needle, there are two notches for thread to rest in: a right position and a left position. You can choose either one—I'm sliding mine into the right position. (Again, these are there so you can run two threads for a twin needle.)

 

Just below that, you'll see two little wire coil thread guides. Guide the thread into the rightmost coil. Finally, thread the eye of the needle from front to back.

 


 

2. Inserting the Bobbin and Pulling Up the Lower Thread

 

To insert your loaded bobbin case, look for the top divot on the machine and align it with the bar extending off the top of the bobbin case. Center it on the rod, line up the bar, and press firmly in the middle until you hear it click into place.

 

Now for the final threading step:

 

  1. Hold the needle thread loosely in your left hand.
  2. Turn the flywheel on the right side of the machine toward you. The needle will dip down and come back up.
  3. As the needle rises, gently pull the thread in your hand. You'll see it catch the bobbin thread and pull up a loop.
  4. Grab that loop and pull it through until you have a full strand.

 

Pass both threads through the slot in your presser foot so they lie toward the back left. Slide the throat plate tabs back into place, press down on the front, and the machine is ready to sew.

 


 

3. Testing Your First Stitches

 

To test your machine, place a piece of fabric—I'm using some of my new Memento fabric (Click to Grab yours here) —under the presser foot and lower the lever.

 

Turn the flywheel toward you by hand for one full rotation to make sure everything clears smoothly. Then, press the foot pedal to sew.

 

When you're finished:

 

  1. Raise the presser foot lever.
  2. Pull your fabric out to the left.
  3. Use the built-in thread cutter blade behind the needle assembly to clip your thread tails.

 

Check your stitch quality on both the top and bobbin side to confirm your balance looks clean.

 


 

4. How to Wind a Bobbin

 

  1. Place your thread on one of the spool pins.
  2. Bring the thread around and behind the silver bobbin winding tension disc, making sure it clicks securely between the discs.
  3. Take your empty bobbin and feed the thread tail from the inside out through one of the holes in the top rim.
  4. Pull the slack out, place the bobbin onto the winding post with the tail pointing straight up, and push the silver latch up against the post.
  5. Disengage the needle mechanism by pulling the flywheel outward.
  6. Hold your thread tail straight up, hit the foot pedal, and wind your bobbin.

 

Once full, cut the thread from the spool, return the bobbin latch to its original position, push the flywheel back in, and remove your wound bobbin.

 


 

5. Changing the Needle

 

I use Schmetz universal needles. (Click to Grab Yours Here)
When you look closely at a needle, you'll see one side of the shank is flat.

 

  1. Ensure the flat side faces away from you (toward the back of the machine).
  2. Loosen the needle clamp screw by turning it toward you.
  3. Slide the needle up into the shaft as far as it will go.
  4. Tighten the needle clamp screw securely.

 


 

6. Machine Controls and Settings

 

  • Tension Dial: Adjusts upper thread tension to balance your stitches. Stitch balance relies on both this dial and the bobbin case tension.
  • Stitch Pattern Selector: Lets you choose between utility and decorative stitches.
  • Modifier Dial: Switches between the orange and white indicator dots, matching whichever color pattern set you want to sew from the dial.
  • Stitch Length Knob: Sets your stitch density based on stitches per inch.
  • Presser Foot Pressure: Adjusts how firmly the foot presses against your fabric.

 


 

7. The Reversible Throat Plate (Single-Hole vs. Zigzag)

 

A standout feature on the Kenmore 158.14310 is its reversible throat plate:

 

  • Oval Opening: Used for standard zigzag and decorative stitches where the needle moves side to side.
  • Single-Hole Opening: Flip the plate over to reveal the single round needle hole.

 

The single-hole plate is ideal for straight stitching delicate, lightweight, or stretchy fabrics. Because there's no wide slot, it prevents the fabric from getting sucked down into the needle hole and jamming. Just remember: only use straight stitches with this setting, or the needle will hit the plate and break.

 

I hope this guide helps you get your Kenmore 158.14310 threaded, adjusted, and ready for your next project. Happy sewing!

 

Contact Us:

Phone: (740)224-0700
Address: 103 East 3rd Street
                Uhrichsville, OH 44683
Hours: Tues., Wed., Fri., & Sat. 10-5, 
Thursday 12-7
            *Closed Sunday & Monday

Privacy Policy | Return Policy | Shipping Policy |  Contact Us


Follow us on...